Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Waco?
Gate repair in Waco typically runs $175 to $650 for common fixes like a stuck slide gate, a failed sensor, or a control board that’s stopped responding. A full operator replacement usually lands between $900 and $2,400 depending on the unit and whether the gate hardware needs work at the same time. We give a written estimate before any work starts, and the estimate is free.
We’re gate specialists, not generalists. Every job on our schedule is a gate job, which means the technician who pulls into your driveway has spent the day diagnosing gate motors, arms, boards and access hardware, not splitting time between gates and half a dozen other trades. That focus is why we can usually tell you what a repair will cost after one visit rather than three.
Gate Repair Cost Breakdown (2026)
Here’s what the common repair categories look like across the Waco market this year. These are typical ranges, not quotes for your specific gate. The written estimate sets the final price.
| Repair Type | Typical Range |
|---|---|
| Manual gate adjustment (sagging, dragging, hinge or latch realignment) | $175 – $400 |
| Safety sensor or photo-eye replacement | $200 – $450 |
| Control board replacement (residential) | $350 – $750 |
| Control board replacement (commercial, DoorKing or FAAC class) | $600 – $1,400 |
| Swing arm operator replacement (FAAC, LiftMaster, Viking) | $700 – $1,600 |
| Slide gate operator replacement | $900 – $2,400 |
| Keypad, receiver, or remote system replacement | $200 – $550 |
| Wheel, track, roller and guide work on a slide gate | $250 – $800 |
| Battery backup or low-voltage power fault diagnosis and repair | $180 – $500 |
| New automated gate installation (operator and hardware) | $2,800 – $7,500 |
What pushes a job toward the top of a range? Commercial operators cost more than residential ones because the parts are heavier and the boards carry more inputs. A gate where the operator failed because the gate itself is dragging will need both fixed, or the new operator fails the same way. Accessories add up too: a card reader, an intercom, or a loop detector wired into the system means more wiring to trace when something stops working. And brand matters. A Mighty Mule or Ghost Controls unit at a home in Woodway is a different job from a DoorKing system at a multi-unit entrance off Valley Mills Drive. We work on nine brands, so the brand on your gate is rarely the reason we can’t help.
What Affects Gate Repair Pricing in Waco
- Gate type and weight. A light residential swing gate and a heavy commercial slide gate are not the same repair even when the symptom sounds identical. Weight drives operator sizing, hinge wear, and how much labor it takes to move panels safely.
- Operator brand and age. Parts availability varies by brand. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule all come through our shop, but a discontinued board can change the math from a repair to a replacement.
- Residential versus commercial. Commercial entrances usually have more access hardware, more than one point of control, and stricter expectations about uptime. All of that adds diagnostic time.
- Wiring and power. A gate is only as reliable as the low-voltage run feeding it. Frayed wiring, a failed transformer, or a buried line that’s taken on water will show up as an “operator problem” when the operator is fine.
- How long it’s been failing. A gate that’s been binding for months wears the operator harder than one that stopped yesterday. The longer it runs out of adjustment, the more parts are in play by the time we see it.
- Waco summers. Central Texas heat is hard on control boards, batteries, and the plastic and rubber parts inside an operator housing. A gate that gets full afternoon sun will go through batteries and board components faster than one in shade, and we see that pattern across McLennan County every summer.
Can You Repair an Electric Gate the Same Day in Waco?
Yes, in many cases. Sensor faults, remote and receiver problems, keypad failures, control board swaps on common units, and manual gate adjustments are usually straightforward once we’ve diagnosed them. We answer 24/7, and fast dispatch from 7am to 7pm means a call in the morning often gets a technician to your gate the same day.
Two things can push the work to a second visit: a part that has to be ordered for a brand or model we don’t carry on the truck, and a gate where the operator and the gate hardware both need work. We’d rather tell you that up front than leave you wondering why the gate still drags after the motor was swapped. When you call, have the brand name and any model info from the operator housing handy. It shortens the diagnosis.
For a broader look at what we handle day to day, see our gate repair page.
What Happens When You Call
You describe the gate. We ask what it’s doing: not opening, opening partway, reversing, beeping, dead to the remote, or moving on its own. From there we book a visit and send a technician who works on gates only. On site, the diagnosis covers the full system, from the motor to the keypad: the operator, the control board, the safety sensors, the access hardware, and the gate leaf itself.
You get a written estimate before any repair starts. If it’s a repair-or-replace decision, we’ll tell you which one makes sense and why. Sometimes a $300 board fixes a gate that looks like a $2,000 problem. Sometimes the honest answer is that the operator is past saving and the money is better spent on a new unit. We’ll say so either way.
Call (855) 638-3208. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
How to Save on Gate Repair
Start with the free estimate. It costs nothing to find out what’s actually wrong, and it stops you from paying for a part you didn’t need. A few other things that keep the bill down:
- Call at the first sign of trouble. A gate that’s started reversing or moving slowly is telling you something. Fixing it early is almost always cheaper than waiting until the operator gives out.
- Keep the track and hinges clear. Debris, gravel, and overgrown vegetation along a slide gate’s track cause drag, drag wears out operators, and worn operators cost more than a cleared track. This is the single cheapest habit a gate owner has.
- Don’t keep pressing the remote. If the gate won’t move, repeated attempts can burn out a board that was still repairable. Stop and call.
- Get the replacement quote while we’re already there. If the diagnosis points to replacement, we can quote a new installation on the same visit. That’s one trip, not two, and it means you’re comparing repair against replacement with real numbers instead of guesses.
- Ask us to check the accessories at the same time. If a technician is already diagnosing the operator, having them test the sensors, keypad, and receiver costs far less than booking separate visits later.
One safety note. Gate operators run on line voltage, and the control box holds a capacitor that can hold a charge after the power is off. Heavy swing and slide panels can crush. Don’t open the operator housing or work on the wiring yourself, and don’t prop or block a moving gate to “test” it. A trained technician should handle anything inside the control box. That’s not us being protective of the work. It’s a genuine hazard.
Is It Cheaper to Repair or Replace a Gate Operator in Waco?
Repair is cheaper when the operator is under roughly eight to ten years old and the fault is isolated to one component, such as a board, a sensor, a receiver, or an arm. Replacement usually wins when the operator is older, has failed more than once in a short span, or when the gate hardware itself is dragging and has already worn out one motor. A board replacement on a residential unit typically runs $350 to $750. A new slide operator installed runs $900 to $2,400. If the gate needs hinge, wheel, or track work on top of a new operator, those numbers move up.
The useful test is this: compare the repair cost against the age and remaining life of the unit. Putting a $700 repair into a fifteen-year-old operator with an obsolete board rarely pays off. Putting the same $700 into a five-year-old LiftMaster or FAAC unit usually does. We’ll give you both numbers and a plain recommendation. Call (855) 638-3208 and we’ll set up the estimate.
What Does New Gate Installation Cost in Waco?
A new automated gate installation in Waco typically runs $2,800 to $7,500, with the range driven by gate size, material, operator class, and how much access hardware goes in. A single residential driveway swing gate with a consumer-grade operator sits near the bottom. A commercial slide gate at a multi-unit entrance with loop detectors, keypads, and a heavier operator sits near the top. Manual gates without an operator cost less, and we install those too.
Installation is a different conversation from repair, and it’s worth having it with someone whose only job is gates. Posts go to proper footing depth for the gate’s weight, the operator gets sized to the leaf, and the safety devices get placed where they actually sense a person or a vehicle. Getting any of that wrong is how a new gate ends up needing repair work in its first year. If you’re weighing a fix against a fresh install, we’ll walk you through both.
FAQs – Gate Repair Cost
How much does gate repair cost in Waco?
Most gate repairs in Waco fall between $175 and $650. Sensor and receiver work sits at the low end, control board and operator replacements at the high end, and commercial systems run higher than residential ones because the parts and diagnostic time are heavier. Call (855) 638-3208 for an exact quote. Estimates are free.
Do you charge a service call fee?
No. The estimate is free, and the price is set per job by the written estimate we give you before work starts. There’s no separate diagnostic or trip charge added on top. Call (855) 638-3208 to book one.
Why is my electric gate not opening, and what will it cost to fix?
The most common causes are a tripped safety sensor, a dead battery in the operator, a failed receiver, or a control board fault. Repair typically runs $180 to $750 depending on which one it is. Sensors and receivers are the cheaper fix, boards are the pricier one. We diagnose the whole system before quoting, so you’re not paying for a guess. Call (855) 638-3208.
Can you repair commercial gate operators, or only residential?
Both. We work on residential and commercial systems from the same roster of technicians, including commercial-grade operators from FAAC, BFT, and DoorKing. Commercial control board work typically runs $600 to $1,400, and slide operator replacement $900 to $2,400. Call (855) 638-3208 for a site visit.
How much does it cost to replace a gate motor in Waco?
A swing arm operator replacement typically runs $700 to $1,600, and a slide gate operator replacement $900 to $2,400. The spread comes down to operator class, gate weight, and whether the gate hardware needs adjustment at the same time. Call (855) 638-3208 and we’ll quote both the repair and the replacement so you can compare.
Which gate brands do you work on?
Nine: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers everything from a Mighty Mule unit on a residential driveway in Hewitt to a DoorKing system at a commercial entrance. If your brand is on that list, we’ve diagnosed it before. If you’re not sure, call (855) 638-3208 and we’ll tell you.
Book a Free Gate Repair Estimate in Waco
Whether it’s a driveway gate that won’t open, a sensor that keeps tripping, or a commercial entrance that’s become a daily headache, the fastest way to a real number is a free estimate. We’ll diagnose the system, tell you what it takes to fix it, and give you the replacement figure too if that’s the smarter call. Gate Repair Waco has served Central Texas since 2018, and every job we take is a gate job. Call (855) 638-3208. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. You can also start with our Gate Repair Waco home page to see how we work.
Pricing reflects the Waco market as of 2026. Gate Repair Waco offers free estimates – call (855) 638-3208.
What Our Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Heather Sutton"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Bryce Pruitt"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Megan Brooks